|
Mfg: Thomas & Betts
Published: 2012
Version: Cat3
1484
pages
And with the industry’s most efficient distribution system, we’re prepared to meet your ongoing MRO, OEM and construction needs down the road. We design integrated solutions with higher quality materials, fewer parts and ease of installation coupled with maintenance in mind in order to reduce product lifecycle costs.
Add to My Library
|
|
|
Mfg: Thomas & Betts
Published: 1996
Version: GM-101
1418
pages
The Thomas & Betts method of installing compression connectors on power cables is designed to provide a high degree of reliability in electrical wiring. COLOR-KEYED connectors not only identify the correct installing die to be used for positive compressions, but also indicate the proper placement of the die on the connector.
Add to My Library
|
|
|
Mfg: Thomas & Betts
Published:
Version: Catalog
1408
pages
Rigid Metal Conduit or Intermediate Metal Conduit ~--- Threadless opening in a sheet metal box or enclosure. Method of Bonding For 120/208 volts or 120/240 volts cir-cuits provided no un punched rings remain around the knockout. For under or over 250 volts circuits, service equipment and hazardous locations (where applicable) provided no un punched rings remain around the knockout.
Add to My Library
|
|
|
Mfg: Thomas & Betts
Published: 2003
Version: GM-101 Vol 1
1396
pages
For over 100 years, Thomas & Betts has been successfully applying innovative design and manufacturing techniques to meet the changing needs of the marketplace. The Thomas & Betts Fittings in this section are produced from many materials and by many manufacturing methods, each carefully selected for its end use suitability.
Add to My Library
|
|
|
Mfg: Thomas & Betts
Published: 2000
Version: GM-1031
1048
pages
A few examples of the three digit identification system for thinwall fittings are: TK-111 "" steel, compression type coupling Installation using either slotted or Phillips screwdriver head, 35-in-lb of torque onto the EMT. NOTE: Excessive torque could damage EMT or housing. USE: To join rigid or IMC conduit at right angles where lack of room prevents using a standard sweep elbow, or to terminate a run of rigid or IMC conduit at a box.
Add to My Library
|
|
|
Mfg: Thomas & Betts
Published: 2003
Version: GM-102
804
pages
For over 100 years, Thomas & Betts has been successfully applying innovative design and manufacturing techniques to meet the changing needs of the marketplace. We deliver the solutions that make your job easier and offer the power to bring it all together in one package. The article includes table references that guide the electrician in the selection of the proper box size necessary to safely accommodate electrical service requirements.
Add to My Library
|
|
|
Mfg: Thomas & Betts
Published:
Version: GM-101
686
pages
Electrical raceways require accessory fittings that provide the mechanical strength, ground continuity and environmental integrity of the system. An additional drawback of hot dip coating is that the lower ductility of the alloyed interface layer that is formed during the hot dip process can cause spalling if the item is deformed after coating.
Add to My Library
|
|
|
Mfg: Thomas & Betts
Published:
Version: GM-102
686
pages
The article includes table references that guide the electrician in the selection of the proper box size necessary to safely accommodate electrical service requirements. This reprinted material is not the complete and official position of the NFPA on the referenced subject which is represented only by the standard in its entirety.
Add to My Library
|
|
|
Mfg: Thomas & Betts
Published: 2012
Version: Cat2
636
pages
For over 100 years, Thomas & Betts has successfully applied innovative design and manufacturing techniques to meet the changing needs of the marketplace. Every Thomas & Betts Customer Service Representative is right where the action is — surrounded by all the support and information they need to answer your questions and fill your orders faster than ever.
Add to My Library
|
|
|
Mfg: Thomas & Betts
Published: 2008
Version: GM-102 Vol 2
612
pages
We deliver the solutions that make your job easier and offer the power to bring it all together in one package. Triple--Iayer protection- including two layers of expoxy coating- stopping corrosion in its tracks and to reduce inventory & cost, conduit body covers come standard with an Integral gasket.
Add to My Library
|
|